GLOSSARY ENTRY (DERIVED FROM QUESTION BELOW) | ||||||
---|---|---|---|---|---|---|
|
13:12 Feb 12, 2020 |
English to Russian translations [PRO] Tech/Engineering - Energy / Power Generation / GEARS | |||||||
---|---|---|---|---|---|---|---|
|
| ||||||
| Selected response from: Enote Local time: 00:36 | ||||||
Grading comment
|
Summary of answers provided | ||||
---|---|---|---|---|
4 | нарезание бочкообразных зубьев на шестерне |
| ||
3 | утончение профиля зубьев (малой) шестерни |
|
утончение профиля зубьев (малой) шестерни Explanation: Сабж (barrelling) - это коррекция профиля зуба (шестерни) в строну его утончения. Посмотрим на описание сабжа у них Цитата из http://www.tandwiel.info/en/gears/tooth-form-corrections/ (там есть рисунки) 2 Barreling and end relief The barreling and the end relief are tooth shape corrections in axial sense. At the barreling the tooth thickness reduces slightly from the middle of the tooth to the sides according to a convex profile. At alignment errors the load remains roughly in the middle of the tooth and one avoids lateral tooth forces, there where the tooth can capture less load. Barreling also allows greater alignment errors when mounting with a retention of a central tooth load. ... 3 Tooth tip barreling The tooth tip is milled convexly across the entire tooth width. This type of gear is applied with tooth couplings to allow a certain alignment error at the connected shafts. Еще одно определение сабжа в том же смысле, но с другим направлением утончения приведено в стандарте ISO 21771:2007 Gears — Cylindrical involute gears and gear pairs — Concepts and geometry, статья 6.2.3. этого стандарта с определением сабжа и рисунком воспроизведена тут https://www.smartmt.com/wp-content/uploads/7CylindricalGearM... 6.2.3 Profile crowning (barrelling), Cα Profile crowning is the continuously increasing relief of the transverse profile from a common defined point of the main geometry (diameter, length of roll, roll angle) in the direction of the tip and root of the gear teeth. See Figure 27. Т.е. этот термин описывает утончение в трех разных направлениях - продольном (бочкообразное), радиальном и верхушки зуба |
| |
Login to enter a peer comment (or grade) |
barrelling of the pinion нарезание бочкообразных зубьев на шестерне Explanation: . -------------------------------------------------- Note added at 20 mins (2020-02-12 13:33:34 GMT) -------------------------------------------------- Gear crowning/barrelling Crowned gears are necessary where noise is a concern. Crowning gear teeth reduces noise by alleviating misalignment through either assembly or thrust problems. Our barrelling machines are used for cleaning and polishing metal and plastics and can give a variety of finishes included matt and shine. http://www.bandhgears.co.uk/gear_crowning.php -------------------------------------------------- Note added at 21 mins (2020-02-12 13:34:04 GMT) -------------------------------------------------- crowning teeth cutting - нарезание бочкообразных зубьев http://www.multitran.com/m.exe?s=нарезание бочкообразных зуб... -------------------------------------------------- Note added at 24 mins (2020-02-12 13:37:27 GMT) -------------------------------------------------- ГОСТ 16530-83. ПЕРЕДАЧИ ЗУБЧАТЫЕ. Общие термины, определения и обозначения 1.7.3. Бочкообразная модификация зуба Бочкообразная модификация Продольная модификация зуба, в результате которой номинальная линия зуба начинает в средней части отклоняться от теоретической линии зуба в его тело с монотонным возрастанием отклонения по мере удаления от середины зуба к его торцам http://docs.cntd.ru/document/gost-16530-83 -------------------------------------------------- Note added at 4 hrs (2020-02-12 17:22:08 GMT) -------------------------------------------------- Благодаря наклону и бочкообразной форме зубьев конические колеса с круговым зубом более прочны, бесшумны (см. выше Crowning gear teeth reduces noise) и допускают большие отклонения при: монтаже, чем прямозубые. [17] Для нарезания цилиндрических шестерен с бочкообразной формой зуба на зубофрезерных станках устанавливается специальное копирное приспособление. http://www.ngpedia.ru/id566448p2.html |
| |
Login to enter a peer comment (or grade) |
Login or register (free and only takes a few minutes) to participate in this question.
You will also have access to many other tools and opportunities designed for those who have language-related jobs (or are passionate about them). Participation is free and the site has a strict confidentiality policy.