Glossary entry (derived from question below)
English term or phrase:
cutting nut
Russian translation:
гайка с пропилом
Added to glossary by
YaroslavShvayko
Feb 14, 2020 03:51
4 yrs ago
16 viewers *
English term
cutting nut
English to Russian
Tech/Engineering
Mechanics / Mech Engineering
bolting
Only for welded bolts this could be not possible, then galling needs to be prevented when loosening the nuts by the following procedure:
1. Apply cleaning lubricant (like WD-40), not in scope of TechnipFMC;
2. Remove dirt carefully with a cloth and brush;
3. Apply cleaning lubricant (like WD-40);
4. Clean the thread with a cutting-nut;
5. Remove remaining dirt carefully with a cloth and brush;
6. Apply lubricant grease any type of oil can be used, however Graphite grease or grease containing Molybdenum disulfide (e.g. Molykote P-37 paste or equivalent) is recommended to use. Lubrication grease is not in scope of TechnipFMC;
7. Then carefully remove the nuts.
1. Apply cleaning lubricant (like WD-40), not in scope of TechnipFMC;
2. Remove dirt carefully with a cloth and brush;
3. Apply cleaning lubricant (like WD-40);
4. Clean the thread with a cutting-nut;
5. Remove remaining dirt carefully with a cloth and brush;
6. Apply lubricant grease any type of oil can be used, however Graphite grease or grease containing Molybdenum disulfide (e.g. Molykote P-37 paste or equivalent) is recommended to use. Lubrication grease is not in scope of TechnipFMC;
7. Then carefully remove the nuts.
Proposed translations
(Russian)
3 | гайка с пропилом | Enote |
3 +1 | плашка (калибровочная) | Aleksey Smirnov |
Change log
Feb 14, 2020 03:51: changed "Kudoz queue" from "In queue" to "Public"
Proposed translations
5 hrs
Selected
гайка с пропилом
Пропил (разрез) с одной стороны гайки нужен для сбора грязи и ржавчины, иначе она будет гоняться по самой резьбе и песок может задрать резьбу.
Вот ссылка с описанием процесса https://zen.yandex.ru/media/sdelaem_sami/opytnyi-slesar-poka...
Вот ссылка с описанием процесса https://zen.yandex.ru/media/sdelaem_sami/opytnyi-slesar-poka...
4 KudoZ points awarded for this answer.
+1
1 hr
плашка (калибровочная)
Для калибровки резьб, нарезанных другими инструментами (резцами, фрезами), применяют плашки с резьбовым диаметром d 56...135 мм и выше.
http://texinfo.inf.ua/razdeli/reg_instr/rezbovi_4.html
Также может быть и резьбонарезная плашка...
Предназначена для нарезания резьбы на различных поверхностях.
http://texinfo.inf.ua/razdeli/reg_instr/rezbovi_4.html
Также может быть и резьбонарезная плашка...
Предназначена для нарезания резьбы на различных поверхностях.
Peer comment(s):
agree |
Nikolai Sergeichuk
: Я думаю, что в инструкции не написали бы о самодельной гайке с прорезью, хотя, конечно, Енот убедительно перевел..
11 hrs
|
Спасибо!
|
Something went wrong...